It is possible to lock/unlock all doors (including the lift gate), and activate the panic alarm by using the keyfob from outside the vehicle.

Before locking the doors, make sure the key is not left in the vehicle.

The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle.

(The effective distance depends upon the conditions around the vehicle.) As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.

The keyfob will not function:
- When the keyfob is not within the operational range.

- When the doors are open or not closed securely.

- When the key is in the ignition switch.

- When the battery is discharged.

The remote keyless entry keyfob transmits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft navigation and communication systems. Do not operate the keyfob while on an airplane.

Make sure the buttons are not operated unintentionally when the unit is stored during a flight.

The following conditions or occurrences will damage the keyfob.

- Do not allow the keyfob to become wet.

- Do not drop the keyfob.

- Do not strike the keyfob sharply against another object.

- If the outside temperature is below 148F (-108C) degrees, the battery of keyfob may not function properly.

- Do not place the keyfob for an extended period in an area where temperatures exceed 1408F (608C).

If a keyfob is lost or stolen, NISSAN recommends erasing the ID code of that keyfob. This will prevent the keyfob from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please contact a NISSAN dealer.

If the indicator light on the keyfob does not illuminate when pushing the buttons, the keyfob battery may be discharged.

For information regarding the replacement of a battery, see “Battery replacement” in the “8.

Maintenance and do-it-yourself” section.

How to use remote keyless entry system

How to use remote keyless entry system

1 LOCK button
2 UNLOCK button
3 PANIC button

Locking doors

1. Remove the key from the ignition switch.

2. Close all the doors.

3. Push the LOCK button 1 on the keyfob.

4. All the doors will lock.

All of the doors will lock when the LOCK button is pushed even though a door remains open.

5. The hazard indicator flashes twice and the horn chirps once.

- When the LOCK button is pushed with all doors locked, the hazard indicator flashes twice and the horn chirps once as a reminder that the doors are already locked.

- Operate the door handles to confirm that the doors have been securely locked.

Unlocking doors

1. Push the UNLOCK button 2 on the keyfob.

- The driver’s door unlocks.

- The hazard indicator flashes once if all doors are completely closed.

2. Push the UNLOCK button again within 5 seconds.

- All the doors and the lift gate unlock.

- The hazard indicator flashes once if all doors are completely closed.

All doors will be locked automatically unless one of the following operations is performed within 1 minute of pushing the UNLOCK button.

- Any door or lift gate is opened.

- The ignition switch is turned to the ON position.

Using panic alarm

If you are near your vehicle and feel threatened, you may activate the alarm to call attention as follows:

1. Push the PANIC button 3 on the keyfob for more than 1 second.

2. The theft warning alarm and headlights will stay on for 25 seconds.

3. The panic alarm stops when:
- It has run for 25 seconds, or
- Any of the buttons on the keyfob is pushed. (Note: the PANIC button must be pushed for more than 1 second.)

Setting hazard indicator and horn mode

This vehicle is set in hazard indicator and horn mode when you first receive the vehicle.

In hazard indicator and horn mode, when the LOCK button 1 is pushed, the hazard indicator flashes twice and the horn chirps once.

When the UNLOCK button 2 is pushed, the hazard indicator flashes once.

If the horn chirp is not necessary, you can switch to hazard indicator only mode by following the switching procedure.

In hazard indicator only mode, when the LOCK button is pushed, the hazard indicator flashes twice. When the UNLOCK button is pushed, neither the hazard indicator nor the horn operates.

Switching procedure:

To switch the hazard indicator and horn operation, push the LOCK 1 and UNLOCK 2 buttons on the keyfob simultaneously for more than 2 seconds.

- When the hazard indicator mode is set, the hazard indicator flashes 3 times.

- When the hazard indicator and horn mode is set, the hazard indicator flashes once and the horn chirps once.