Front seats
Manual seat adjustment
Forward and backward:
Pull the lever1 up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position.
Reclining:
To recline the seatback, pull the lever2 up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. (See “Precautions on seat belt usage” later in this section.) Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission in the P (Park) position.
Sliding front passenger seat (CrossCabriolet models):
To slide the front passenger seat from the front most position to the rear most position, push the bottom half of the seatbackA or the front seat cushion B . If you push the top half of the seatback C , it will lock the seat in the front most position.
Seat lifter (if so equipped):
Pull up or push down the adjusting lever to adjust the seat height until the desired position is achieved.
Lumbar support (if so equipped):
The lumbar support feature provides lower back support to the driver.
Move the lever 1 up or down to adjust the seatback lumbar area.
Power seat adjustment
Operating tips:
• The power
seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
• Do not operate
the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
See “Automatic drive positioner” in the “3. Predriving checks and adjustments” section for the seat position memory function (if so equipped).
Forward and backward:
Moving the switchA forward or backward will slide the seat forward or backward to the desired position.
Pushing the front 1 or back 2 end of the slide switchB will slide the driver seat forward or backward to the desired position (Cross- Cabriolet models driver’s seat only).
Reclining:
Move the recline switchA backward until the desired angle is obtained. To bring the seatback forward again, move the switchA forward.
Push and hold the back2 end of the reclining switch B until the desired angle is obtained.
To bring the seatback forward again, push and hold the front 1 end of the switch (Cross- Cabriolet models driver’s seat only).
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. (See “Precautions on seat belt usage” later in this section.) Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission is in the P (Park) position.
Seat lifter (if so equipped):
Push the front or rear end of the switch up or down to adjust the angle of the front portion or height of the seat.
Lumbar support (if so equipped):
The lumbar support feature provides lower back support to the driver.
Push the front1 or back2 end of the switch to adjust the seatback lumbar area.
Front passenger’s seatback switch
Remote walk-in switch
Walk-in function (front passenger seat, CrossCabriolet models):
CAUTION
• When
operating the walk-in function,
be sure not to contact any
moving parts to avoid possible injuries
and/or damages.
• When operating
the walk-in function,
be sure that the front passenger
seat is not occupied by a
passenger and/or any objects to
avoid possible injuries and/or damages.
• After operating
the walk-in function,
be sure to return the seat to the
rearmost position and then tilt up
the seatback until it latches.
This feature makes it easier to get in and out of the rear seat. Use the following procedure when getting in and out of the rear seat on the passenger’s side. If the sun visor is used, close it to the original position before operating the walk-in feature.
1. Push the front passenger’s seatback switch to fold down the seatback and unlock the seat position.
Alternatively, you can push the remote walkin switch located on the instrument panel to fold down the front passenger’s seatback and unlock the seat position.
2. Slide the seat forward to the foremost
position manually.
3. Get in or out the vehicle.
4. Return the front passenger seat to the
rearmost position. To slide the front passenger
seat, see “Manual seat adjustment”
earlier in this section.
Driver’s seatback release (CrossCabriolet models)
To exit the rear seat from the driver’s side, pull the strap behind the driver’s seat to release the driver’s seatback. The driver’s seatback will tilt forward so that you can exit the vehicle.
NOTE:
Pulling the strap behind the driver’s seat does not slide the driver’s seat forward.
You cannot slide the driver’s seat manually.
WARNING
Before using the driver’s seatback release, be sure that the driver’s seat is not occupied by a driver and/or any objects to avoid possible injuries and/ or damage.
See also:
Break-in schedule
During the first 1,200 miles (2,000 km), follow these recommendations to obtain
maximum engine performance and ensure the future reliability and economy of your
new vehicle. Failure to follow th ...
Bluetooth® Hands-Free Phone System without Navigation System (if so
equipped)
WARNING
● Use a phone after stopping your vehicle
in a safe location. If you have to use a
phone while driving, exercise extreme
caution at all times so full attention may
be given to vehic ...
Continuously Variable Transmission (CVT) fluid
- Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluids.
- Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage
the CVT, which is not covered by the NISSAN ...